Velleman-projects K3502 Assembly instructions Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Velleman-projects K3502 Assembly instructions. Velleman projects K3502 Assembly instructions User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 16
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Parking Radar
K3502
ILLUSTRATED ASSEMBLY MANUAL H3502IP-2
Total solder points: 185
Difficulty level: beginner 1 2 3 4 5 advanced
U
s
e
a
s
p
a
r
k
i
n
g
a
i
d
,
o
r
a
s
e
y
e
s
f
o
r
r
o
b
o
t
p
r
o
j
e
c
t
s
.
Vue de la page 0
1 2 3 4 5 6 ... 15 16

Résumé du contenu

Page 1 - Parking Radar

Parking Radar K3502 ILLUSTRATED ASSEMBLY MANUAL H3502IP-2 Total solder points: 185 Difficulty level: beginner 1  2  3  4  5  advanced Use as p

Page 2

10  Install the print behind the bores using spacing sleeves, so that the sensors are facing the bores properly without touching the housing.

Page 3

11 Installation  Close the housing as watertight as possible f.i. by using silicone.  Surch for a suitable place somewhere in the trunk,

Page 4 - RECT MOUNTING SEQUENCE !

12  Connect the receiver to the base print.  Connect the terminal GND of the base print to the - of the car (chassis)  Connect the terminal ‘+’ of

Page 5

13 P3502B GND +V RW S1 S2 P3502B P3502S GND +V RW DIS + GND GND+V RW DIS S1 S2 S1 S2 + - Connection

Page 6 -  Be sure to put the longest

14 7. Schematic diagram (Control section) Schematic diagram

Page 7

15 PCB PCB layout P3502S PCB layout P3502B 8. PCB’s

Page 8 - 8. IC mounting

16 Modifications and typographical errors reserved © Velleman Components nv. H3502IP - 2004 - ED2 VELLEMAN Components NV Legen Heirweg 33 9890 Gavere

Page 9 - 4. INSTALLATION IN THE CAR

2 Specifications:  Detection range : 5cm - 1,5m (adjustable)  Detection angle : 5°  Transmitter frequency : 40KHz.  Sample frequency : 26Hz.  Po

Page 10

3 Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project s

Page 11 - POSITION OF SENSOR HOLES

4 Assembly hints 1.3 Soldering Hints : 1- Mount the component against the PCB surface and carefully solder the leads 2- Make sure the solder join

Page 12 - 6. USE

5  R1 : 10M (1 - 0 - 6 - B)  R2 : 22K (2 - 2 - 3 - B)  R3 : 27K (2 - 7 - 3 - B)  R4 : 27K (2 - 7 - 3 - B)  R5 : 47 (4 - 7 - 0

Page 13 - Connection

6 Construction  C6 : 470µF 7. Electrolytic capacitor. Watch the polarity ! C...  RV1 : 470K RV18. Trim Potentiometer  J1 :

Page 14 - Schematic diagram

7  T1 : BC547B 3. Transistor  R7 : 15K (1 - 5 - 3)  R8 : 15K (1 - 5 - 3)  R9 : 15K (1 - 5 - 3)  R10 : 15K (1 - 5

Page 15 - 8. PCB’s

8 Construction  SENS 1 : MA40A5S or eq.(marked with T).  SENS 2 : MA40A5R or eq. (marked with CTD)  Either on the print or connect them to

Page 16 - 5 410329 291594

9  Connect the points GND, +V, RW, DIS, S1 and S2 of the main PCB to the corresponding points on the receiver PCB.  Make sure that the distance betw

Commentaires sur ces manuels

Pas de commentaire